Completed Project
Dodge Grand Caravan Oil Leak Repair in Kirkland, WA: Leaking Oil Filter Housing Under the Intake
·
2017 Dodge Grand Caravan SXT, 3.6L Pentastar V6, automatic, front-wheel drive (120,853 miles)
·
Kirkland, WA

Project Details
Vehicle
2017 Dodge Grand Caravan SXT, 3.6L Pentastar V6, automatic, front-wheel drive (120,853 miles)
Location
Kirkland, WA
Completed
Time in Shop
Opened Nov 9; completed Nov 17
Investment
$1,950–$2,550 (completed November 2026)
Details above come from our job records for this project.
This 2017 Grand Caravan SXT (120,853 miles, 3.6L V6) came in with a rattle at low speed. We found the rattle, and on the inspection we also found a large oil leak from the top of the engine. We replaced the leaking oil filter housing, the drive belt, tensioner and idler pulley, and flushed the brake fluid.

The underside on the lift. Oil covered the bottom of the engine, the oil pan and the crossmember.
What we found
The rattle came from the belt tensioner. Its pulley rattled whenever the A/C compressor engaged, which is likely the noise the owner was hearing. The idler pulley bearing was loud and whining too, and the belt was worn.

The worn belt and the tensioner. The tensioner rattled when the A/C compressor engaged.
The inspection also flagged a large oil leak from the valley at the top of the engine. On the Pentastar, the oil filter housing sits in that valley under the intake manifold, where you can’t see it with the intake on. Our technician put a borescope down the intake, found a lot of oil under the manifold, and traced it to the oil filter housing.
The oil had run down the engine and onto the A/C compressor. The A/C itself was working fine, blowing 40°F at the vent.

The A/C compressor covered in oil. It looked like engine oil, with no sign of a leak directly above it.
The inspection also noted a small valve cover leak, and the oil was about 4,000 miles past its change interval.
The work performed
Oil filter housing replacement: $1,250–$1,600. About 2.5 hours of labor. We:
Removed the upper and lower intake manifolds
Removed the old oil filter housing and plugged the openings in the engine
Cleaned the leaked oil out of the valley
Installed a new genuine Mopar oil filter housing and torqued it to spec
Reassembled the intake with a new MAHLE intake gasket set
Changed the engine oil (full synthetic 5W-20) and cleaned the bottom of the engine
Road tested it, with no further issues
More on our engine repair service.
Drive belt, tensioner and idler pulley: $550–$700. New Litens tensioner and idler pulley and a new Bando belt, then a test drive. See belts and hoses replacement.
Brake fluid flush: $150–$250. The brake fluid tested high for copper, so we flushed the master cylinder, calipers and lines with new DOT 3 fluid and bled the system. More on our brake fluid flush.

The brake fluid test strip. High copper content means the fluid is due.
What we recommended but didn’t do
The inspection found a small coolant leak at the thermostat housing. We quoted both the inner and outer thermostat housings at $600–$750. The owner held off on this visit, and our note says to monitor it.

The small leak at the thermostat housing. Recommended, not done on this visit.
We also noted no record of a transmission fluid service and suggested checking whether it had been done.
What it cost
The visit landed in the $1,950–$2,550 range, completed November 2026. Most of it was the oil filter housing: the housing itself plus the labor to take the intake apart and put it back together.
That range reflects a completed historical project, not a current quote.
Questions about this job
Why did the intake have to come off for an oil leak?
On this engine the oil filter housing sits under the intake manifold. To replace it, we removed the upper and lower intake.
How did you find the leak?
Oil was all over the bottom of the engine. Our technician put a borescope down the intake, found oil pooled under the intake manifold, and traced it to the oil filter housing.
What was the rattle?
The belt tensioner pulley, rattling when the A/C compressor engaged. The idler pulley bearing was also whining, so we replaced the belt, tensioner and idler together.
Was the thermostat housing fixed?
No. It had a small leak, and the owner held off on it this visit. We noted it to monitor.
Do you work on Dodge minivans?
Yes. More on our Dodge repair in Kirkland.
Prepared from our job records for this vehicle: the repair order and technician notes, the multi-point inspection with photos, the parts list and the final invoice.
Dealing with something similar?
Tell us what your vehicle is doing and we’ll take a look.
© Totem Lake Auto Care, 2026
Privacy Policy · Terms of Service · Made in USA
