Completed Project

GMC Sierra Axle Seal Replacement and Differential Service in Kirkland, WA: Leaking Front Axle Seals at 215,000 Miles

·

2001 GMC Sierra 1500 SL, 4.8L Vortec V8, manual, four-wheel drive (215,125 miles)

·

Kirkland, WA

Oil covering the front axle housing on a 2001 GMC Sierra 1500 4x4

Project Details

Vehicle

2001 GMC Sierra 1500 SL, 4.8L Vortec V8, manual, four-wheel drive (215,125 miles)

Location

Kirkland, WA

Completed

Time in Shop

Opened Oct 30; completed Nov 13

Investment

$2,900–$3,450 (completed November 2026)

Details above come from our job records for this project.

This 2001 GMC Sierra 1500 4x4 (215,125 miles, 4.8L V8, manual) came in for an oil service and inspection. The inspection turned up low, dirty fluid in both differentials, oil on the front axle housing, and worn steering parts. We replaced the front axle seals and the worn steering parts, serviced both differentials, and changed the power steering and brake fluid.

What we found

Both the front and rear differential fluid were low and dirty, and the front axle housing and the area around it were covered in oil.

Oil covering the front axle housing and CV axle area on the 2001 Sierra

The front axle housing, wet with oil. Both differentials were low and dirty.

Another view of the oily front axle housing on the Sierra

Another angle on the front axle housing before the work.

In the steering, every component had wear and play except the two outer tie rods. The power steering fluid was worn, and the brake fluid tested with copper content north of 100.

Fluid comparison card with the Sierra’s power steering fluid next to new fluid

The fluid card. New fluid on top, this truck’s fluid below.

Brake fluid test strip for the Sierra next to the copper scale

Brake fluid test strip. Copper level was north of 100.

The transmission shifted fine and its fluid was in good condition, and the transfer case was full and clean.

The work performed

Front axle seals, differential service and steering parts: $2,300–$2,900. About 6.5 hours of labor. We:

  • Removed the front wheels, tie rod ends and sway bar end links

  • Separated the upper control arms from the knuckles and pulled the CV axles from the hubs

  • Moved the axle housing, removed the axle shafts and replaced both axle seals with genuine GM seals

  • Reinstalled the axle shafts, axle housing, axles and upper control arms

  • Installed new sway bar end links

  • Replaced the inner and outer tie rods on both sides

  • Replaced the idler arm with a genuine GM part

  • Serviced the front and rear differential fluid with full synthetic 75W-90 gear oil

  • Cleaned the oil off the axle housing

  • Had a four-wheel alignment done at a partner shop

  • Test drove it and checked for leaks

More on our CV axle and drivetrain repair, our steering and suspension work, and wheel alignment.

Oil cooler block-off plate gasket: $70–$130. Replaced the gasket and cleaned up the oil mess.

Oil residue around the oil filter area on the Sierra’s 4.8L

Oil seepage around the oil filter area on the 4.8L V8.

Oil service: $120–$180. Full synthetic 5W-30, a genuine GM oil filter, a new drain plug gasket, a tire rotation and the multi-point inspection. See our oil change service.

Drain plug from the Sierra held over the drain pan, coated in old fluid

A drain plug from this visit, coated in old fluid.

Power steering fluid service: $60–$90. Refilled with genuine GM power steering fluid.

Brake fluid flush: $140–$220. Flushed the master cylinder, calipers and lines with new DOT 3 fluid and bled the system. More on our brake fluid flush.

What we recommended but didn’t do

The left front wheel bearing was tight but starting to make noise. We quoted it at $700–$900, and the owner held off on this visit.

The inspection also noted that the parking brake could use an adjustment, both license plate lights and the front right turn/marker light weren’t wired in, and the third brake light and cargo light assembly had failed.

What it cost

The visit landed in the $2,900–$3,450 range, completed November 2026. Most of it was the axle seal, differential and steering job: about 6.5 hours of labor plus the seals, tie rods, idler arm, end links, gear oil and the alignment.

That range reflects a completed historical project, not a current quote.

Questions about this job

Why replace the axle seals during a differential service?

The front axle housing was covered in oil and both differentials were low. We replaced the axle seals, refilled both differentials, cleaned the housing, and checked for leaks after the test drive.

What steering parts were replaced?

Inner and outer tie rods on both sides, the idler arm, and the front sway bar end links. Everything except the outer tie rods had wear and play at inspection; we replaced the outers along with the inners.

Did it need an alignment?

Yes. After new tie rods and an idler arm, a partner shop did a four-wheel alignment.

What about the wheel bearing?

The left front bearing was tight but starting to make noise. It was quoted, and the owner held off for now.

Do you work on older GM trucks?

Yes. More on our GMC repair in Kirkland.

Prepared from our job records for this vehicle: the repair order and technician notes, the multi-point inspection with photos, the parts list and the final invoice.

Dealing with something similar?

Tell us what your vehicle is doing and we’ll take a look.

Our Location

13637 NE 126th Pl, Kirkland, WA 98034